Topcon GTS-823A Manuel d'utilisateur Page 104
- Page / 144
- Table des matières
- MARQUE LIVRES
Noté. / 5. Basé sur avis des utilisateurs
9-5
9 CHECK AND ADJUSTMENT
9.3.1 Checking /Adjusting the Plate Level
Adjustment is required if the axis of the plate level is not perpendicular to the vertical axis.
l
Check
1) Place the plate level parallel to a line running through the centers of two leveling screws, say, A and
B. Use these two leveling screws only and place the bubble in the center of the plate level.
2) Rotate the instrument 180° or 200g around the vertical axis and check bubble movement of the
plate level. If the bubble has been displaced, then proceed with the following adjustment.
l
Adjustment
1) Adjust the level adjustment capstan screw, with the accessory adjusting pin and return the bubble
towards the center of the plate level. Correct only one-half of the displacement by this method.
2) Correct the remaining amount of the bubble displacement with the leveling screws.
3) Rotate the instrument 180° or 200g around the vertical axis once more and check bubble
movement. If the bubble is still displaced, then repeat the adjustment.
9.3.2 Checking /Adjusting the Circular Level
Adjustment is required if the axis of the circular level is also not perpendicular to the vertical axis.
l
Check
1) Carefully level the instrument with the plate level only. If the bubble of the circular level is centered
properly, adjustment is not required. Otherwise, proceed with the following adjustment.
l
Adjustment
1) Shift the bubble to the center of the circular level, by adjusting three capstan adjustment screws on
the bottom surface of the circular level, with the accessory adjusting pin.
Leveling screw A
Plate level
Leveling screw B
Level adjustment
capstan screw
Half amount of displacement
Capstan adjustment
screws
Bottom of the base
- GTS-820A 1
- FOREWORD 3
- Storage in the case 4
- Display for Safe Use 5
- Safety Cautions 5
- Laser Safety 7
- Contents 8
- FOREWORD 10
- Standard Set Composition 11
- 1 NOMENCLATURE AND FUNCTIONS 12
- 1.2 Display 14
- 1.3 Operating Key 15
- Page Display 17
- Function 17
- 1.5 Star key ( 18
- X:+0°00'00" 19
- Y:+0°00'00" 19
- X: 19
- Y: 19
- 20
- 1882KByte 20
- 315KByte 20
- 1.6 Auto Power Off 22
- 1.7 Data Output 22
- 1.8 Rotating Method 22
- Turn-round function 23
- Transmit 24
- Mode setting 24
- 2 PREPARATION FOR MEASUREMENT 25
- 2.3 Power Switch Key ON 27
- 2003-10-10 15:30:40 28
- 2003-07-10 15:30:40 29
- 2.8 Resume Mode ON/OFF 32
- 2.10 Memory Card 33
- Prism constant value : 0mm 34
- Prism constant value : 30mm 34
- COLLIMATION 36
- V : 90°10'20" 37
- HD: < PPM 0.0 37
- VD: (m) *c.R 37
- MEAS MODE VH SD NEZ P1↓ 37
- 3.2 Automatic Collimation 38
- 3.4.1 Setting Items 40
- 1) Search Patterns 40
- 2) Search Range 40
- 3) Wait Time 41
- 4) Tracking Speed 41
- 5) Reflector type 41
- 6) Prediction operating time 41
- SD HD NEZ 0SET HOLD 44
- 4.2 Distance Measurement 47
- 1)Setting the number of times 48
- 2)Measuring Method 48
- MEAS MODE VH SD NEZ 49
- 4.3 COORDINATE MEASUREMENT 52
- TURN HT MEAN m/ft SET P2 53
- HT MEAN m/ft SET P2 54
- N : 55
- MEAS MODE VH SD HD P1 55
- 4.4 DATA OUTPUT 57
- 2003-10-10 15:30:40 59
- HD * 61
- SET OK? YES NO 62
- 5.5 Line Measurement (LINE) 69
- Sight L 70
- p 7/7 73
- OFFSET MEASUREMENT 73
- 1.FREE V-ANGLE 73
- 2.HOLD V-ANGLE 73
- HD: m 74
- HD* < m 74
- SD : m 77
- HD : m 79
- HR : 9 79
- HR : 95 80
- 5.7 External Link 81
- Parameters 82
- (3)Setting Parameters of RC 83
- Parameters 83
- 6.3 Rename a File 87
- 6.2 Protect a File 87
- 6.4 Deleting a File 88
- 6.5 Copy a File 88
- 6.6 Initializing Memory 89
- 7.2 Data File In 91
- 7.3 Data File Out 91
- Serial port 94
- Setting parameters for RS232C 94
- Setting parameter for RC 94
- 8.2 Setting Parameters 96
- Establishing a Password 97
- Changing a Password 99
- Changing the Password 99
- IMPORTANT: 99
- 9 CHECK AND ADJUSTMENT 100
- 9.2 Checking the Optical Axis 101
- 2003-10-10 14:30:40 116
- CURVATURE 122
- 13 POWER SOURCE AND CHARGING 123
- 14 DETACH/ATTACH OF TRIBRACH 125
- 15 BATTERY SYSTEM 126
- 16 PRISM SYSTEM 127
- 17 PRECAUTIONS 128
- 18 ERROR DISPLAYS 129
- 19 SPECIAL ACCESSORIES 130
- 20 SPECIFICATIONS 133
- Atmospheric conditions 134
- Condition 1 Condition 2 134
- APPENDIX 137
- APPENDIX-2 138
- APPENDIX-3 139
- APPENDIX-4 140
- EMC NOTICE 142
Produits connexes et manuels pour Mesure, test et contrôle Topcon GTS-823A
(168 pages)© 2020, manymanuals.fr. Tous droits réservés | 0.044 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Commentaires sur ces manuels